Hitachi L100 User manual

HITACHI

L100 Series Inverter

Instruction Manual

• Single-phase Input 200V Class

• Three-phase Input 200V Class

• Three-phase Input 400V Class

After reading this manual,

keep it handy for future reference.

Hitachi, Ltd.

Tokyo Japan

Manual Number: NB576XA

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

L100 Inverter

xv

Safety Messages .................................................................................................................. iii

Hazardous High Voltage ..................................................................................................... iii

General Precautions - Read These First! ..............................................................................iv

Precautions for EMC (Electromagnetic Compatibility) .......................................................vi

Index to Warnings and Cautions in This Manual ............................................................... vii

General Warnings and Cautions ......................................................................................... xii

Revisions .......................................................................................................................... xvii

Chapter 1: Getting Started

Introduction .......................................................................................................................1–2

L100 Inverter Specifications .............................................................................................1–4

Introduction to Variable-Frequency Drives ......................................................................1–7

Frequently Asked Questions ...........................................................................................1–12

Chapter 2: Inverter Mounting and Installation

Orientation to Inverter Features ........................................................................................2–2

Basic System Description ..................................................................................................2–5

Step-by-Step Basic Installation .........................................................................................2–6

Powerup Test ...................................................................................................................2–17

Using the Front Panel Keypad ........................................................................................2–19

Chapter 3: Configuring Drive Parameters

Choosing a Programming Device .....................................................................................3–2

Using Keypad Devices ......................................................................................................3–3

Using the PC Software — DOP Plus ................................................................................3–6

“D” Group: Monitoring Functions ....................................................................................3–8

“F” Group: Main Profile Parameters .................................................................................3–9

“A” Group: Standard Functions ......................................................................................3–10

“B” Group: Fine Tuning Functions .................................................................................3–21

“C” Group: Intelligent Terminal Functions ....................................................................3–27

Chapter 4: Operations and Monitoring

Introduction .......................................................................................................................4–2

Connecting to PLCs and Other Devices ............................................................................4–4

Using Intelligent Input Terminals .....................................................................................4–6

Using Intelligent Output Terminals .................................................................................4–18

Analog Input Operation ...................................................................................................4–24

Analog and Digital Monitor Output ................................................................................4–25

PID Loop Operation ........................................................................................................4–27

Configuring the Inverter for Multiple Motors .................................................................4–28

Table of Contents

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

Table of Contents

xvi

Chapter 5: Motor Control Accessories

Introduction .......................................................................................................................5–2

Component Descriptions ...................................................................................................5–3

Chapter 6: Troubleshooting and Maintenance

Troubleshooting ................................................................................................................6–2

Monitoring Trip Events, History, & Conditions ...............................................................6–5

Restoring Factory Default Settings ...................................................................................6–8

Maintenance and Inspection .............................................................................................6–9

Warranty .........................................................................................................................6–14

Appendix A: Glossary and Bibliography

Glossary ...........................................................................................................................A–2

Bibliography ....................................................................................................................A–8

Appendix B: Drive Parameter Settings Tables

Introduction ...................................................................................................................... B–2

Parameter Settings for Keypad Entry .............................................................................. B–2

Parameter Settings for DOP/DRW/DOP Plus ................................................................. B–7

Index

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

L100 Inverter

i

Safety Messages

For the best results with the L100 Series inverter, carefully read this manual and all of

the warning labels attached to the inverter before installing and operating it, and follow

the instructions exactly. Keep this manual handy for quick reference.

Definitions and Symbols

A safety instruction (message) includes a hazard alert symbol and a signal word,

WARNING or CAUTION. Each signal word has the following meaning:

HIGH VOLTAGE: This symbol indicates high voltage. It calls your attention to items

or operations that could be dangerous to you and other persons operation this equipment.

Read the message and follow the instructions carefully.

This symbol is the “Safety Alert Symbol.” It occurs with either of two signal words:

CAUTION or WARNING, as described below.

WARNING: Indicates a potentially hazardous situation which, if not avoided, can result

in serious injury or death.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, can result

in minor to moderate injury, or serious damage to the product. The situation described in

the CAUTION may, if not avoided, lead to serious results. Important safety measures

are described in CAUTION (as well as WARNING), so be sure to observe them.

1 Step 1: Indicates a step in a series of action steps to accomplish a goal.

NOTE: Notes indicate an area or subject of special merit, emphasizing either the

product’s capabilities or common errors in operation or maintenance.

TIP: Tips give a special instruction that can save time or provide other benefits while

installing or using the product. The tip calls attention to an idea that may not be obvious

to first-time users of the product.

Hazardous High Voltage

HIGH VOLTAGE: Motor control equipment and electronic controllers are connected to

hazardous line voltages. When servicing drives and electronic controllers, there may be

exposed components with housings or protrusions at or above line potential. Extreme

care should be taken to protect against shock.

Stand on an insulating pad and make it a habit to use only one hand when checking com-

ponents. Always work with another person in case an emergency occurs. Disconnect

power before checking controllers or performing maintenance. Be sure equipment is

properly grounded. Wear safety glasses whenever working on electronic controllers or

rotating machinery.

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

ii

General Precautions - Read These First!

WARNING: This equipment should be installed, adjusted, and serviced by qualified

electrical maintenance personnel familiar with the construction and operation of the

equipment and the hazards involved. Failure to observe this precaution could result in

bodily injury.

WARNING: The user is responsible for ensuring that all driven machinery, drive train

mechanism not supplied by Hitachi, Ltd., and process line material are capable of safe

operation at an applied frequency of 150% of the maximum selected frequency range to

the AC motor. Failure to do so can result in destruction of equipment and injury to

personnel should a single-point failure occur.

WARNING: For equipment protection, install a ground leakage type breaker with a fast

response circuit capable of handling large currents. The ground fault protection circuit is

not designed to protect against personal injury.

HIGH VOLTAGE: HAZARD OF ELECTRICAL SHOCK. DISCONNECT INCOM-

ING POWER BEFORE WORKING ON THIS CONTROL.

WARNING: Wait at least five (5) minutes after turning off the input power supply

before performing maintenance or an inspection. Otherwise, there is the danger of

electric shock.

CAUTION: These instructions should be read and clearly understood before working

on L100 series equipment.

CAUTION: Proper grounds, disconnecting devices and other safety devices and their

location are the responsibility of the user and are not provided by Hitachi, Ltd.

CAUTION: Be sure to connect a motor thermal cutoff switch or overload device to the

L100 series controller to assure that the inverter will shut down in the event of an

overload or an overheated motor.

HIGH VOLTAGE: Dangerous voltage exists until power light is off. Wait at least 5

minutes after input power is disconnected before performing maintenance.

WARNING: This equipment has high leakage current and must be permanently(fixed)

hard-wired to earth via two independent cables.

WARNING: Rotating shafts and above-ground electrical potentials can be hazardous.

Therefore, it is strongly recommended that all electrical work conform to the National

Electrical Codes and local regulations. Installation, alignment and maintenance should

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

L100 Inverter

iii

be performed only by qualified personnel.

Factory-recommended test procedures included in the instruction manual should be

followed. Always disconnect electrical power before working on the unit.

CAUTION:

a) Class I motor must be connected to protective earth via low resistive path (< 0.1ohm)

b) Any motor used must be of a suitable rating.

c) Motors may have hazardous moving parts. In this event suitable protection must be

provided.

CAUTION: Alarm connection may contain hazardous live voltage even when inverter is

disconnected. When removing the front cover for maintenance or inspection, confirm

that incoming power for alarm connection is completely disconnected.

CAUTION: Hazardous (main) terminals for any interconnection (motor, contact

breaker, filter, etc.) must be inaccessible in the final installation.

CAUTION: This equipment should be installed in IP54 or equivalent (see EN60529)

enclosure. The end application must be in accordance with BS EN60204-1. Refer to the

section on inverter mounting, starting on page 2–6. The diagram dimensions are to be

suitably amended for your application.

CAUTION: Connection to field wiring terminals must be reliably fixed having two

independent means of mechanical support. Using a termination with cable support

(figure below), or strain relief, cable clamp, etc.

CAUTION: A double-pole disconnection device must be fitted to the incoming mains

supply close to the inverter. Additionally, a protection device meeting IEC947-1/

IEC947-3 must be fitted at this point (protection device data shown in page 2–13).

NOTE: The above instructions, together with any other requirements are highlighted in

this manual, and must be followed for continued LVD (European Low Voltage Directive)

compliance.

Terminal (spade lug) Cable support

Cable

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

iv

Precautions for EMC (Electromagnetic Compatibility)

You are required to satisfy the EMC directive (89/336/EEC) when using an L100

inverter in a European country. To satisfy the EMC directive and to comply with

standard, follow the checklist below.

WARNING: This equipment should be installed, adjusted, and serviced by qualified

personal familiar with construction and operation of the equipment and the hazards

involved. Failure to observe this precaution could result in bodily injury.

1. The power supply to L100 inverter must meet these specifications:

a. Voltage fluctuation+/- 10% or less

b. Voltage imbalance +/- 3% or less

c. Frequency variation +/- 4% or less

d. Voltage distortion THD = 10% or less

2. Installation measure:

a. Use a filter designed for L100 inverter

3. Wiring:

a. Shielded wire (screened cable) is required for motor wiring, and the length must

be less than 50 meters.

b. The carrier frequency setting must be less than 5 kHz to satisfy EMC require-

ments.

c. Separate the main circuit from the signal/process circuit wiring.

4. Environmental conditions - when using a filter, follow these guidelines:

a. Ambient temperature: -10 to 40 °C

b. Humidity: 20 to 90% RH (non-condensing)

c. Vibration: 5.9 m/sec

2

(0.6 G) 10 ~ 55Hz

d. Location: 1000 meters or less altitude, indoors (no corrosive gas or dust)

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

L100 Inverter

v

Index to Warnings and Cautions in This Manual

Installation - Cautions for Mounting Procedures

Wiring - Warnings for Electrical Practices and Wire Specifications

CAUTION: Be sure to install the unit on flame-resistant material

such as a steel plate. Otherwise, there is the danger of fire.

........... 2–6

CAUTION: Be sure not to place any flammable materials near the

inverter. Otherwise, there is the danger of fire.

........... 2–6

CAUTION: Be sure not to let the foreign matter enter vent openings

in the inverter housing, such as wire clippings, spatter from welding,

metal shavings, dust, etc. Otherwise, there is the danger of fire.

........... 2–6

CAUTION: Be sure to install the inverter in a place which can bear

the weight according to the specifications in the text (Chapter 1,

Specifications Tables). Otherwise, it may fall and cause injury to per-

sonnel.

........... 2–6

CAUTION: Be sure to install the unit on a perpendicular wall which

is not subject to vibration. Otherwise, it may fall and cause injury to

personnel.

........... 2–6

CAUTION: Be sure not to install or operate an inverter which is

damaged or has missing parts. Otherwise, it may cause injury to per-

sonnel.

........... 2–6

CAUTION: Be sure to install the inverter in a well-ventilated room

which does not have direct exposure to sunlight, a tendency for high

temperature, high humidity or dew condensation, high levels of dust,

corrosive gas, explosive gas, inflammable gas, grinding-fluid mist,

salt damage, etc. Otherwise, there is the danger of fire.

........... 2–6

WARNING: “Use 60/75°C Cu wire only” or equivalent. ......... 2–12

WARNING: “Open Type Equipment.” ......... 2–12

WARNING: “A Class 2 circuit wired with Class 1 wire” or equiva-

lent.

......... 2–12

WARNING: “Suitable for use on a circuit capable of delivering not

more than 5,000 rms symmetrical amperes, 240 V maximum.” For

models with suffix N or L.

......... 2–12

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

vi

Index to Warnings and Cautions in This Manual

Wiring - Cautions for Electrical Practices

WARNING: “Suitable for use on a circuit capable of delivering not

more than 5,000 rms symmetrical amperes, 240 V maximum.” For

models with suffix N or L.

........ 2–12

HIGH VOLTAGE: Be sure to ground the unit. Otherwise, there is a

danger of electric shock and/or fire.

........ 2–12

HIGH VOLTAGE: Wiring work shall be carried out only by quali-

fied personnel. Otherwise, there is a danger of electric shock and/or

fire.

........ 2–12

HIGH VOLTAGE: Implement wiring after checking that the power

supply is off. You may incur electric shock and/or fire.

........ 2–12

HIGH VOLTAGE: Do not connect wiring to an inverter or operate

an inverter that is not mounted according the instructions given in

this manual. Otherwise, there is a danger of electric shock and/or

injury to personnel.

........ 2–12

WARNING: Make sure the input power to the inverter is off. If the

drive has been powered, leave it off for five minutes before continu-

ing.

........ 2–16

CAUTION: Be sure that the input voltage matches the inverter

specifications: • Single/Three phase 200 to 240 V 50/60 Hz (up to

2.2kW) • Three phase 200 to 230V 50/60Hz (above 2.2kW) • Three

phase 380 to 460 V 50/60Hz

........ 2–14

CAUTION: Be sure not to input a single phase to a three-phase-

only type inverter. Otherwise, there is the danger of fire.

........ 2–14

CAUTION: Be sure not to connect an AC power supply to the

output terminals. Otherwise, there is the danger of injury and/or

fire.

........ 2–14

Power Input Power Output

L1 L2 L3

T1 T2 T3

UVW

(L) (N)

NOTE:

L, N:

L1, L2, L3:

Single-phase 200 to 240V 50/60 Hz

Three-phase 200 to 240V 50/60 Hz

Three-phase 380 to 460V 50/60 Hz

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

L100 Inverter

vii

Powerup Test Caution Messages

CAUTION: Fasten the screws with the specified fastening torque

(see the following table). Check for any loosening of screws. Other-

wise, there is the danger of fire.

......... 2–15

CAUTION: Remarks for using earth leakage circuit breakers in the

mains supply: Frequency inverters with CE-filters (RFI-filter) and

shielded (screened) motor cables have a higher leakage current

toward Earth GND. Especially at the moment of switching on this

can cause inadvertent tripping of earth leakage circuit breakers.

Because of the rectifier on the input side of the inverter there is the

possibility to stall the switch-off function through small amounts of

DC current. Please observe the following: • Use only short time-

invariant and pulse current-sensitive earth leakage circuit breakers

with higher trigger current. • Other components should be secured

with separate earth leakage circuit breakers. • Earth leakage circuit

breakers in the power input wiring of an inverter are not an absolute

protection against electric shock by direct touching.

......... 2–15

CAUTION: Be sure to install a fuse in the wire for each phase of

the main power supply to the inverter. Otherwise, there is the

danger of fire.

......... 2–15

CAUTION: For motor leads, earth leakage breakers and electro-

magnetic contactors, be sure to size these components properly

(each must have the capacity for rated current and voltage). Other-

wise, there is the danger of fire.

......... 2–15

CAUTION: The heat sink fins will have a high temperature. Be

careful not to touch them. Otherwise, there is the danger of getting

burned.

......... 2–17

CAUTION: The operation of the inverter can be easily changed

from low speed to high speed. Be sure check the capability and

limitations of the motor and machine before operating the inverter.

Otherwise, there is the danger of injury.

......... 2–17

CAUTION: If you operate a motor at a frequency higher than the

inverter standard default setting (50Hz/60Hz), be sure to check the

motor and machine specifications with the respective manufacturer.

Only operate the motor at elevated frequencies after getting their

approval. Otherwise, there is the danger of equipment damage.

......... 2–18

CAUTION: Check the following before and during the powerup

test. Otherwise, there is the danger of equipment damage. • Is the

shorting bar between the +1 and + terminals installed? DO NOT

power or operate the inverter if the jumper is removed. • Is the

direction of the motor correct? • Did the inverter trip during acceler-

ation or deceleration? • Were the rpm and frequency meter readings

as expected? • Were there any abnormal motor vibrations or noise?

......... 2–18

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

viii

Index to Warnings and Cautions in This Manual

Warnings for Operations and Monitoring

WARNING: Be sure to turn on the input power supply after closing

the front case. While being energized, be sure not to open the front

case. Otherwise, there is the danger of electric shock.

.......... 4–3

WARNING: Be sure not to operate the switches with wet hands.

Otherwise, there is the danger of electric shock.

.......... 4–3

WARNING: While the inverter is energized, be sure not to touch

the inverter terminals even when the motor is stopped. Otherwise,

there is the danger of electric shock.

.......... 4–3

WARNING: If the Retry Mode is selected, the motor may suddenly

restart during the trip stop. Do not approach the machine (be sure to

design the machine so that safety for personnel is secure even if it

restarts.) Otherwise, it may cause injury to personnel.

.......... 4–3

WARNING: If the power supply is cut off for a short period of time,

the inverter may restart operation after the power supply recovers if

the command to operate is active. If a restart may pose danger to

personnel, so be sure to use a lock-out circuit so that it will not

restart after power recovery. Otherwise, it may cause injury to

personnel.

.......... 4–3

WARNING: The Stop Key is effective only when the Stop function

is enabled. Be sure to enable the Key separately from the

emergency stop. Otherwise, it may cause injury to personnel.

.......... 4–3

WARNING: After the operation command is given, if the alarm

reset is conducted, it will restart suddenly. Be sure to set the alarm

reset after verifying the operation command is off. Otherwise, it

may cause injury to personnel.

.......... 4–3

WARNING: Be sure not to touch the inside of the energized

inverter or to put any conductive object into it. Otherwise, there is a

danger of electric shock and/or fire.

.......... 4–3

WARNING: When the power is turned on when the running

command is already active, the motor will suddenly start rotation

and is dangerous. Before turning the power on, confirm that the

running command is not enabled.

.......... 4–3

WARNING: When the Stop key function is disabled, pressing the

Stop key does not cancel the stop and trip.

.......... 4–3

WARNING: Be sure to provide a separate, hard-wired emergency

stop switch. When the operation command source is a digital opera-

tor, this selection is ineffective.

.......... 4–3

WARNING: If the power is turned on and the Run command is

already active, the motor starts rotation and is dangerous! Before

turning power on, confirm that the Run command is not active.

.......... 4–6

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

L100 Inverter

ix

Cautions for Operations and Monitoring

Warnings and Cautions for Troubleshooting and Maintenance

WARNING: After the Reset command is given and the alarm reset

occurs, the motor will restart suddenly if the Run command is

already active. Be sure to set the alarm reset after verifying that the

Run command is off to prevent injury to personnel.

......... 4–16

CAUTION: The heat sink fins will have a high temperature. Be

careful not to touch them. Otherwise, there is the danger of getting

burned.

........... 4–2

CAUTION: The operation of the inverter can be easily changed

from low speed to high speed. Be sure check the capability and

limitations of the motor and machine before operating the inverter.

Otherwise, it may cause injury to personnel.

........... 4–2

CAUTION: If you operate a motor at a frequency higher than the

inverter standard default setting (50Hz/60Hz), be sure to check the

motor and machine specifications with the respective manufacturer.

Only operate the motor at elevated frequencies after getting their

approval. Otherwise, there is the danger of equipment damage.

........... 4–2

CAUTION: It is possible to damage the inverter or other devices in

your application if the maximum current or voltage characteristics

of a connection point are exceeded.

........... 4–4

WARNING: Wait at least five (5) minutes after turning off the input

power supply before performing maintenance or an inspection.

Otherwise, there is the danger of electric shock.

........... 6–2

WARNING: Make sure that only qualified personnel will perform

maintenance, inspection, and part replacement. (Before starting to

work, remove any metallic objects from your person (wristwatch,

bracelet, etc.). Be sure to use tools with insulated handles. Other-

wise, there is a danger of electric shock and/or injury to personnel.

........... 6–2

WARNING: Never remove connectors by pulling on its wire leads

(wires for cooling fan and logic p.c.board). Otherwise, there is a

danger of fire or injury due to wire breakage.

........... 6–2

CAUTION: When removing connectors, never pull the wires (wires

for the cooling fan and logic P.C. board. Otherwise, there is danger

of fire due to wire breakage and/or injury to personnel.

........... 6–2

CAUTION: Never test the withstand voltage (HIPOT) on the

inverter. The inverter has a surge protector between the main circuit

terminals above and the chassis ground.

......... 6–12

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

x

General Warnings and Cautions

WARNING: Never modify the unit. Otherwise, there is a danger of electric shock and/

or injury.

CAUTION: Withstand voltage tests and insulation resistance tests (HIPOT) are

executed before the units are shipped, so there is no need to conduct these tests before

operation.

CAUTION: Do not attach or remove wiring or connectors when power is applied. Also,

do not check signals during operation.

CAUTION: Do not stop operation by switching off electromagnetic contactors on the

primary or secondary sides of the inverter.

When there has been a sudden power failure while an operation instruction is active, then

the unit may restart operation automatically after the power failure has ended. If there is

a possibility that such an occurrence may harm humans, then install an electromagnetic

contactor (Mgo) on the power supply side, so that the circuit does not allow automatic

restarting after the power supply recovers. If the optional remote operator is used and

the retry function has been selected, this will also cause automatic restarting when an

operation instruction is active. So, please be careful.

HIGH VOLTAGE: Be careful not to touch wiring or connector

terminals when working with the inverters and taking measure-

ments. Be sure to place the measurement circuitry above in an

insulated housing before using them.

........ 6–13

Power

Input

Inverter

L1, L2, L3

Earth leakage

breaker

U, V, W

Motor

P24

FW

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

L100 Inverter

xi

CAUTION: Do not insert leading power factor capacitors or surge absorbers between

the output terminals of the inverter and motor.

CAUTION: Be sure to connect the grounding terminal to earth ground.

CAUTION: When inspecting the unit, be sure to wait five minutes after tuning off the

power supply before opening the cover.

CAUTION: MOTOR TERMINAL SURGE VOLTAGE SUPPRESSION FILTER

(For the 400 V CLASS)

In a system using an inverter with the voltage control PWM system, a voltage surge

caused by the cable constants such as the cable length (especially when the distance

between the motor and inverter is 10 m or more) and cabling method may occur at the

motor terminals. A dedicated filter of the 400 V class for suppressing this voltage surge

is available. Be sure to install a filter in this situation.

CAUTION: SUPPRESSION FOR NOISE INTERFERENCE FROM INVERTER

The inverter uses many semiconductor switching elements such as transistors and

IGBTs. Thus, a radio receiver or measuring instrument located near the inverter is

susceptible to noise interference.

To protect the instruments from erroneous operation due to noise interference, they

should be used well away from the inverter. It is also effective to shield the whole

inverter structure.

The addition of an EMI filter on the input side of the inverter also reduces the effect of

noise from the commercial power line on external devices.

Note that the external dispersion of noise from the power line can be minimized by

connecting an EMI filter on the primary side of inverter.

Power

Input

Inverter

L1, L2, L3

Earth leakage

breaker

U, V, W

Motor

GND lug

Surge absorber

Leading power

factor capacitor

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

xii

General Warnings and Cautions

CAUTION: EFFECTS OF DISTRIBUTOR LINES ON INVERTERS

In the cases below involving a general-purpose inverter, a large peak current flows on the

power supply side, sometimes destroying the converter module. Where such situations

are foreseen, or the paired equipment must be highly reliable, install an AC reactor

between the power supply and the inverter.

1. The unbalance factor of the power supply is 3% or higher.

2. The power supply capacity is at least 10 times greater than the inverter capacity (and

the power supply capacity, 500 kVA or more).

3. Abrupt power supply changes are expected.

Some examples include:

a.Several inverters are interconnected with a short bus.

b.A thyristor converter and an inverter are interconnected with a short bus.

c:An installed phase advance capacitor opens and closes.

In cases (1), (2), and (3) we recommend installing an AC reactor of 3% (at a voltage

drop at rated current) with respect to the supply voltage on the power supply side.

CAUTION: When the EEPROM error E8 occurs, be sure to confirm the setting value

again.

CAUTION: When setting b contact to the forward or reverse command [FW], [RV]

terminal, the inverter starts automatically. Do not set to b contact without a purpose.

General Caution

CAUTION: In all the illustrations in this manual, covers and safety devices are

occasionally removed to describe the details. While operating the product, make sure

that the covers and safety devices are placed as they were specified originally and

operate it according to the instruction manual.

EMI filter Inverter

Power

source

Motor

U

V

W

U

V

W

L1(L1)

L2

L3(N)

R1

S1

T1

R2

S2

T2

Terminal

for

grounding

Power

source

EMI

filter

Noise

Inverter

Motor

Noise

Remote

operator

Piping

(to be grounded)

or shielded wire

Ground the

frame.

Completely ground the shield made

of metal screen, enclosed panel, etc.

with as short a wire as possible.

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

L100 Inverter

xvii

Revisions

Revision History Table

No. Revision Comments Date of Issue

Operation

Manual No.

Initial Release of Manual NB576X May 1999 NB576X

1 Revision A

Pages 1-4 – Specs tables: added row for input curent,

changed rated input voltage tolerance, corrected dynamic

braking %torque, corrected product weight (lbs)

Page 2-8 – Corrected H dimension for -002 models

August 1999 NB576XA

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

Getting Started

In This Chapter.... page

— Introduction ......................................................2

— L100 Inverter Specifications............................. 4

— Introduction to Variable-Frequency Drives.......7

— Frequently Asked Questions..........................12

1

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

Introduction

Getting Started

1–2

Introduction

Main Features

Congratulations on your purchase of an L100

Series Hitachi inverter! This inverter drive

features state-of-the-art circuitry and components

to provide high performance. The housing

footprint is exceptionally small, given the size of

the corresponding motor. The Hitachi L100

product line includes more than a dozen inverter

models to cover motor sizes from 1/4 horsepower

to 10 horsepower, in either 230 VAC or 460 VAC

power input versions. The main features are:

• Convenient keypad for parameter settings

• Built-in RS-422 communications interface to

allow configuration from a PC and for field bus

external modules.

• Sixteen programmable speed levels

• Two-step acceleration and deceleration curves

• PID control adjusts motor speed automatically to maintain a process variable value

The design in Hitachi inverters overcomes many of the traditional trade-offs between

speed, torque and efficiency. The performance characteristics are:

• V/F (volts-per-hertz) control algorithm, selectable for either constant or reduced

torque loads

• Output frequency range from 0.5 to 360 Hz

• Continuous torque operation at 100% within a 1:10 speed range (6/60 Hz / 5/50 Hz)

without motor derating

A full line of accessories from Hitachi is available to complete your application:

• Digital remote operator keypad

• Dynamic braking unit

• Radio noise filters and EMI filters (shown below)

• CE compliance filters

• DIN rail mounting adapter (35mm rail size)

Model L100-002NFU

EMI Filter

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

L100 Inverter

Getting Started

1–3

Inverter Specifications Label

The Hitachi L100 inverters have product labels located on the right side of the housing,

as pictured below. Be sure to verify that the specifications on the labels match your

power source, motor, and application safety requirements.

Model Number Convention

The model number for a specific inverter contains useful information about its operating

characteristics. Refer to the model number legend below:

Inverter model number

Motor capacity for this model

Output Rating:

Frequency, voltage, current

Manufacturing codes:

Lot number, date, etc.

Specifications label

Regulatory agency approvals

Power Input Rating:

frequency, voltage, phase, current

L100 004 H F U 5

Version number (_, 1, 2, ...)

Restricted distribution:

E=Europe, U=USA

Input voltage:

N = single or three-phase 200V class

H = three-phase 400V class

L = three phase only, 200V class

Applicable motor capacity in kW

001 = 0.1 kW

002 = 0.2 kW

004 = 0.4 kW

005 = 0.55 kW

007 = 0.75 kW

011 = 1.1 kW

015 = 1.5 kW

022 = 2.2 kW

030 = 3.0 kW

037 = 3.7 kW

040 = 4.0 kW

055 = 5.5 kW

075 = 7.5 kW

Configuration type

F = with digital operator (keypad)

Series name

Technologies Inc.

Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com

Page is loading ...

Hitachi L100 User manual

Hitachi L100 User manual

Related papers

Other documents